| Item |
NZ2000 |
| Standard functions |
Control mode |
V/F(Voltage/Frequency) control |
| Sensorless flux vector control (VC) |
| Maximum frequency |
Vector control: 0–320 Hz |
| V/F control: 0–3200Hz |
| Carrier frequency |
1.0–16.0 kHz |
| The carrier frequency is automatically adjusted based on the load features. |
| Input frequency esolution |
Dgital setting: 0.01 Hz |
| Analog setting: 0.025% of maximum frequency |
| Startup torque |
G type: 0.5 Hz/150% (VC); |
| P type: 0.5 Hz/100% (VC) |
| Speed range |
1:100 (VC) |
| Speed stability accuracy |
± 0.2% (VC) |
| Torque control accuracy |
± 20% |
| Overload capacity |
G type: 60s for 150% of the rated current, 3s for 180% of the rated current. |
| P type: 60s for 120% of the rated current, 3s for 150% of the rated current. |
| Torque boost |
Auto boost |
| Customized boost 0.1%–30.0% |
| V/F curve |
Line V/F curve |
| Multi-point V/F curve |
| N-power V/F curve (1.2-power, 1.4-power, 1.6-power,1.8-power, square) |
| V/F separation |
Two types: complete separation; half separation |
| Ramp mode |
Straight-line ramp |
| S-curve ramp |
| Four groups of acceleration/deceleration time with the range of 0.0–6500.0s |
| DC braking |
DC braking frequency: 0.00 Hz to maximum frequency |
| Braking time: 0.0–100.0s |
| Braking action current value: 0.0%–100.0% |
| JOG control |
JOG frequency range: 0.00–50.00 Hz |
| JOG acceleration/deceleration time: 0.0–6500.0s |
| Onboard multiple preset speeds |
It implements up to 16 speeds via the simple PLC function or combination of terminal states |
| Onboard PID |
It realizes process-controlled closed loop control system easily. |
| Auto voltage regulation (AVR) |
It can keep constant output voltage automatically when the mains voltage changes. |
| Overvoltage/ Overcurrent stall control |
The current and voltage are limited automatically during the running process so as to avoid frequent tripping due to overvoltage/over current. |
| Torque limit and control |
It can limit the torque automatically and prevent frequent over current tripping during the running process. |
| Power dip ride through |
The load feedback energy compensates the voltage reduction so that the AC drive can continue to run for a short time. |
| Rapid current limit |
It helps to avoid frequent over current faults of the AC drive. |
| High performance |
Control of asynchronous motor are implemented through the high-performance current vector control technology. |
| Timing control |
Time range: 0.0–6500.0 minutes |
| Communication methods |
RS485 (MODBUS-RTU) |
| Protection mode |
Motor short-circuit detection at power-on, input/output phase loss protection, over current protection, overvoltage protection, under voltage protection, overheat protection and overload protection. |
| Input and output |
Input terminal |
6 digital input terminals, one of which supports up to 100 kHz high-speed pulse input. |
| 2 analog input terminals, one of which only supports 0–10 V voltage input and the other supports 0–10 V voltage input or 4–20 mA current input. |
| Frequency source |
Digital setting, analog voltage setting, analog current setting, pulse setting and serial communication port setting. |
| Auxiliary frequency source |
There are ten auxiliary frequency sources.It can implement fine tuning of auxiliary frequency and frequency synthesis. |
| Running command source |
Operation panel/Control terminals/Serial communication port |
| You can perform switchover between these sources in various ways. |
| Output terminal |
1 digital output terminal |
| 1 relay output terminal |
| 1 analog output terminal :that supports 0–20 mA current output or 0–10 V voltage output |
| operation on the operation panel |
LED display |
It displays the parameters. |
| Key locking and function selection |
It can lock the keys partially or completely and define the function range of some keys so as to prevent mis-function. |
| Environment |
Installation location |
Indoor, free from direct sunlight, dust, corrosive gas,combustible gas, oil smoke, vapour, drip or salt. |
| Altitude |
Lower than 1000 m |
| Ambient temperature |
-10°C ～40°C (de-rated if the ambient temperature is between 40°C and 50°C) |
| Humidity |
Less than 95%RH, without condensing |
| Vibration |
Less than 5.9 m/s2 (0.6 g) |
| Storage temperature |
-20°C～60°C |